+7 (916) 0-100-600

Тел: +7 (916) 0-100-600



Extron System 5 IP FPC SA

Аудио-видео коммутаторы с пятью входами и управлением по Ethernet с помощью IP Link®
Артикул (SKU): 60-397-81


Наличие: Заказ 30-40 дней

381 440,00 руб.
381 440,00 руб.
Extron

Только безналичный расчет, НДС 0%. Цену теперь надо перепроверять перед заказом

Мы продолжаем привозить оборудование, соблюдаем сроки от 2 до 8 недель

Более 10 000 товаров от 30 производителей

Торопитесь, дверца постепенно закрывается

В новых обстоятельствах, поставка только на заказ, требуется предоплата

Описание товара

Подробности

Активный аудиовизуальный коммуатаор с пятью входами и одним выходом, предоставляющие универсальное и доступное решения для аудиовизуальных систем с одним проектором в аудиториях, залах заседаний, конференц-залах и других мультимедиа окружениях. Стандартные функции включают в себя управляемые входы, легкое в использовании обучение ИК ПДУ, управление дисплеем по RS-232, реле для управления помещением и систему контроля и мониторинга по Ethernet IP Link®.

  • Ширина полосы частот RGB видеосигнала - 350 МГц (-3 дБ)
  • Управление дисплеем по RS-232 или ИК
  • Четыре порта управления IR/RS-232
  • Порт мониторинга цифрового входа
  • Предварительно настроенные драйверы

Дополнительная информация

Video
   Gain Unity
   Bandwidth 350 MHz (-3 dB), fully loaded
   Differential phase error 1° at 3.58 MHz and 4.43 MHz
   Differential gain error 1% at 3.58 MHz and 4.43 MHz
   Crosstalk -68 dB @ 10 MHz, -39 dB @ 100 MHz
   Switching speed <600 ms (max.)
 
Video input
   Number/signal type 1 RGBHV, RGBS, RGsB, RsGsBs
2 RGBHV, RGBS, RGsB, RsGsBs, S-video, or composite video
2 S-video or composite video
   Connectors 1 female 15-pin HD (RGB)
2 x 5 female BNC (RGB, S-video, or composite video)
2 x 1 female BNC (composite video) and 2 female 4-pin mini DIN (S-video)
   Nominal level 1 Vp-p for Y of S-video, and for composite video
0.7 Vp-p for RGB
0.3 Vp-p for C of S-video
   Minimum/maximum levels  
      RGB Analog: 0.3 V to 1.5 Vp-p with no offset
      S-video, composite video Analog: 0.4 V to 2.0 Vp-p with no offset
   Impedance 75 ohms
   Horizontal frequency 15 kHz to 145 kHz
   Vertical frequency 30 Hz to 170 Hz
   Return loss  
      RGB <-40 dB @ 5 MHz
      S-video <-25 dB @ 0 to 10 MHz
      Composite video <-40 dB @ 0 to 10 MHz
   DC offset (max. allowable) 1.5 V
 
Video output
   Number/signal type 1 RGBHV, RGBS, RGsB, RsGsBs
1 S-video
1 composite video
   Connectors 5 female BNC (RGB)
2 female BNC (S-video)
1 female BNC (composite video)
   Nominal level 1 Vp-p for Y of S-video, and for composite video
0.7 Vp-p for RGB
0.3 Vp-p for C of S-video
   Minimum/maximum levels  
      RGB Analog: 0.3 V to 1.5 Vp-p (follows input)
      S-video, composite video Analog: 0.4 V to 2.0 Vp-p (follows input)
   Impedance 75 ohms
   Return loss <-40 dB @ 5 MHz
   DC offset ±5 mV with input at 0 offset
   Switching type Triple-Action™ (RGB delay)
 
Sync
   Input type RGBHV, RGBS, RGsB, RsGsBs
   Output type RGBHV, RGBS, RGsB, RsGsBs (follows input)
   Standards TTL (RGB), NTSC 3.58, NTSC 4.43, PAL, SECAM
   Input level 2.0 V to 5.0 Vp-p
   Output level 5.0 Vp-p, unterminated
   Input impedance 10k ohms
   Output impedance 75 ohms
   Max. input voltage 5.0 Vp-p
   Max. propagation delay 30 ns
   Max. rise/fall time 4 ns
   Polarity Positive or negative (follows input)
 
Audio
   Gain  
      Lineout Unbalanced output: 0 dB; balanced output: +6 dB
      Preamp Unbalanced output: -6 dB; balanced output: 0 dB at max. volume
   Frequency response, amplifier models
      Power amp (4 or 8 ohm) 20 Hz to 20 kHz, 0 dB to -1.5 dB @ 1 watt output
      Lineout/preamp 20 Hz to 20 kHz, 0 dB to -0.5 dB
   Frequency response, nonamplifier models
      Lineout/preamp 20 Hz to 20 kHz, 0 dB to -0.5 dB
   THD + Noise <0.15% @ 1 kHz at max. power output
   S/N at max. power output or line level output (unweighted)
      Power amp (amplifier models only) >80 dB at 10 Hz to 22 kHz
      Preamp >-100 dB at 20 Hz to 20 kHz
      Lineout >-110 dB at 10 Hz to 22 kHz
   Crosstalk <-80 dB @ 1 kHz, fully loaded
   Stereo channel separation >80 dB @ 1 kHz
   CMRR >80 dB @ 20 Hz to 200 Hz, >60 dB @ 20 Hz to 20 kHz
   Bass adjustment ±10 dB @ 100 Hz
   Treble adjustment ±10 dB @ 10 kHz
 
Audio input
   Number/signal type 4 stereo or mono, balanced/unbalanced (inputs 1-4)
1 stereo or mono, unbalanced (input 5)
   Connectors (4) 3.5 mm captive screw connectors, 5 pole (inputs 1-4)
(1) 3.5 mm mini audio jack (tip, ring, sleeve) (input 5)
   Impedance >10k ohms unbalanced/balanced, DC coupled
   Nominal level -10 dBV (316 mVrms)
    NOTE    0 dBu = 0.775 Vrms, 0 dBV = 1 Vrms, 0 dBV ≈ 2 dBu
+4 dBu and 0 dBu are professional audio line level standards.
-10 dBV and -20 dBV are semiprofessional, computer audio, and consumer audio standards.
   Maximum level +18 dBu
   Input gain adjustment -40 dB to +30 dB, adjustable per input
 
Audio output — line level (all models)
   Number/signal type 2 stereo or mono, balanced/unbalanced (1 fixed and 1 variable)
   Connectors (2) 3.5 mm captive screw connectors, 5 pole
   Impedance 50 ohms unbalanced, 100 ohms balanced
   Gain error ±0.1 dB channel to channel
   Nominal level -10 dBV (316 mV) or +4 dBu (1.23 V) (configurable)
   Maximum level (600 ohm) >+18 dBu, balanced at 1%THD+N
    NOTE    Unbalanced wired outputs have unity gain/attenuation. Balanced outputs result in a 6 dB gain.
 
Audio output — power amplifier (amplifier models only)
   Number/signal type 1 stereo or mono (default = stereo, configurable via front panel or control software)
   Connector (1) 4 position screw terminal
   Sensitivity -22 dBV (80 mVrms, -19.8 dBu) for max. power output (adjustable)
   Power bandwidth at rated maximum power output
      4 ohm output 10 Hz to 20 kHz, ≤0.5% THD
      8 ohm output 20 Hz to 20 kHz, ≤0.8% THD
   Drive/full power out 40 watts; 20 watts (rms) per channel, 4 or 8 ohm load
   Protection Input limiting, thermal, short circuit
 
Control/remote — switcher host ports
   Serial control port 2 bidirectional RS-232: 1 rear panel female 9-pin D connector
1 front panel 2.5 mm stereo mini jack
   Baud rate and protocol 38400 baud, 8 data bits, 1 stop bit, no parity
   Serial control pin configurations 2 = TX, 3 = RX, 5 = GND (9-pin D)
tip = TX, ring = RX, sleeve = GND (mini stereo jack)
   Ethernet control port 1 female RJ-45
   Ethernet data rate 10/100Base-T, half/full duplex with autodetect
   Ethernet protocol ARP, ICMP (ping), IP, TCP, DHCP, HTTP, SMTP, Telnet
   Ethernet default settings Link speed and duplex level = autodetected
IP address = 192.168.254.254
Subnet mask = 255.255.0.0 
Default gateway = 0.0.0.0
DHCP = off
   Web server Up to 200 simultaneous sessions
7.25 MB nonvolatile user memory
   Extron remote key pad (SCP) control (1) 3.5 mm 5-pole captive screw connector (shared with control module and IR Link port)
   IR remote control IR 402 (optional)
Front panel: 30' maximum, 40 degrees off axis
Rear panel: 38 kHz, hardwired, modulated
   Program control Extron Global Configurator for Windows®
Extron Simple Instruction Set (SIS™)
Microsoft® Internet Explorer ver. 6 or higher, Telnet
 
Control — relay
   Number/type 6 momentary or latching (configurable via software)
   Connectors (3) 3.5 mm captive screw connectors, 3 pole
   Connector configuration Groups A, B, C; each with 1 common and 2 normally open relays (default)
   Contact rating 24 V, 1A
 
Control — serial ports
   Display control port (1) 3.5 mm captive screw connector, 3 pole for bidirectional RS-232 control (±5 V)
   Baud rate and protocol 115200 to 300 baud (9600 baud = default); 8 (default) or 7 data bits; 1(default) or 2 stop bits; 
no parity (default), or even or odd parity
 
Control — IR/serial ports
   IR/serial control ports (4) 3.5 mm captive screw connectors, 2-pole
Programmable: RS-232 (±5 V), or TTL level (0 to 5 V) infrared up to 1 MHz
   Baud rate and protocol (RS-232) 115200 to 300 baud (9600 baud = default); 8 (default) or 7 data bits; 1(default) or 2 stop bits; 
no parity (default), or even or odd parity
   IR learning frequencies 30 kHz to 62 kHz
   IR learning distance 4" (10 cm) to 14" (36 cm) from the front panel
 
Control — digital input monitoring port
   Number/type 1 digital input
   Connector (1) 3.5 mm captive screw connector, 2 poles of a 3 pole connector
    NOTE    These pins can be configured as a digital input or as power sense port.
   Pin configuration G = GND, IN = digital in or power sense
   Digital inputs  
      Input voltage range 0-12 VDC
      Input impedance 10k ohms
      Threshold low to high >0.7 VDC, nonadjustable
      Threshold high to low <0.6 VDC, nonadjustable
 
General
   Power 100 VAC to 240 VAC, 50-0 Hz, 50 watts, internal
   Temperature/humidity Storage: -40 to +158 °F (-40 to +70 °C) / 10% to 90%, noncondensing
Operating: +32 to +111 °F (0 to +43.9 °C) / 10% to 90%, noncondensing
   Cooling Convection, vented on sides and top
   Mounting  
      Rack mount Yes, with included brackets
   Enclosure type Metal
   Enclosure dimensions 1.75" H x 17.5" W x 9.4" D (1U high, full rack wide)
4.4 cm H x 44.4 cm W x 23.9 cm D
(Depth excludes connectors, knob, and buttons. Width excludes rack ears.)
   Product weight 6.0 lbs (2.7 kg)
   Shipping weight 11 lbs (5 kg)
   DIM weight  
      USA/Canada 10 lbs (5 kg)
      International 11 lbs (5 kg)
   Vibration ISTA 1A in carton (International Safe Transit Association)
   Regulatory compliance  
      Safety CE, c-UL, UL
      EMI/EMC CE, C-tick, FCC Class A, ICES, VCCI
      Accessibility Section 508 of the Rehabilitation Act (29 U.S.C. 794d)
   Warranty 3 years parts and labor

Отзывы

Напишите ваш собственный отзыв

Ваш отзыв для: Extron System 5 IP FPC SA

Как вы оцениваете этот товар? *

 1 звезда2 звезды3 звезды4 звезды5 звёзд
Качество
Цена

Вы возможно также заинтересованы в следующих товарах

Extron SCP 226

Extron SCP 226

59 052,80 руб.