Описание товара
Подробности
Обеспечивает высокую надежность и исключительное качество изображения с высоким разрешением, он построен на основе полностью цифровой технологии Extron и обеспечивает идеальную «пиксель-в-пиксель» передачу компьютерного DVI видеоизображения с разрешением до 1920x1200, включая HDTV 1080p/60. Кроме того, в PowerCage FOX DVI Plus предусмотрен режим эмуляции EDID, автоматическое запоминание входов, удаленное управление по RS-232, встроенные тестовые таблицы и мониторинг системы в реальном времени. Несколько плат приемников могут подключаться каскадом.
- Распределение сигналов single-link DVI-D, стерео аудио и управляющих RS-232 на очень большие дистанции по одному оптоволоконному кабелю
- Полностью цифровая технология обеспечивает качество «пиксель-в-пиксель» для сигналов с разрешением до 1920x1200, в т.ч. HDTV 1080p/60
- Модульная конструкция с возможностью модернизации в полевых условиях и «горячей» заменой плат, рассчитанная на шасси PowerCage™ 1600
- Эмуляция EDID
- Возможность каскадного подключения
- Аварийная сигнализация при потере сигнала в оптоволокне
- Автоматическое запоминание входов
Дополнительная информация
| PowerCage™ FOX Rx DVI Plus | |||
| Optical fiber interconnection between transmitter and receiver | |||
|---|---|---|---|
| Number/type | 1 singlemode or 1 multimode fiber optic input and output per board | ||
| |||
| Connectors | 2 bidirectional LC connectors per FOX board | ||
| Operating distance | |||
| Singlemode | 30 km (18.75 miles) with singlemode (SM) cables with a SM board | ||
| Multimode | 300 m (985') with 62.5 µm OM1 multimode (MM) cable and a MM board 1 km (3280') with 50 µm OM2 multimode (MM) cable and a MM board 2 km (6561') with 50 µm OM3/OM4 2000 MHz bandwidth laser optimized MM cable and a MM board | ||
| |||
| Nominal peak wavelength | 850 nm for multimode (MM), 1310 nm for singlemode (SM) | ||
| Transmission power, singlemode or multimode | -5 dBm, typical | ||
| Maximum receiver sensitivity | |||
| Singlemode | -18 dBm, typical | ||
| Multimode | -12 dBm, typical | ||
| Optical loss budget | |||
| Singlemode | 13 dB, maximum | ||
| Multimode | 7 dB, maximum | ||
| Maximum channel data rate | 4.25 Gbps | ||
| Video | |||
| Resolution range | 640x480 up to 1920x1200 @ 60Hz, including 480p, 576p, 720p, 1080i, 1080p @ 60Hz, sampled pixel for pixel; higher resolution 2K (2048x1080) @ 60 Hz, undersampled | ||
| Format | RGB | ||
| Standards | DVI 1.0, HDMI | ||
| Video output | |||
| Number/signal type | 1 single link DVI-D (or HDMI*) | ||
| Connector | 1 female DVI-I | ||
| Nominal level | 0.8 Vp-p | ||
| Video delay | 1-2 frames | ||
| Audio | |||
| |||
| Gain | |||
| Range | Adjustable, -18 dB to +10 dB | ||
| Default | Unbalanced output: -6 dB; balanced output: 0 dB | ||
| Frequency response | 20 Hz to 20 kHz, ±0.5 dB | ||
| THD + Noise | 0.10% @ 1 kHz at nominal level | ||
| S/N | >80 dB at maximum output (unweighted) | ||
| CMRR | 65 dB @ 20 Hz to 20 kHz | ||
| Audio bits per sample | 18 bits per channel, 2 channels (L, R) | ||
| Sampling rate | 48 kHz | ||
| Audio output | |||
| Number/signal type | 1 stereo, balanced/unbalanced or 2 mono, balanced/unbalanced | ||
| Connectors | (1) 3.5 mm captive screw connector, 5 pole | ||
| Impedance | 50 ohms unbalanced, 100 ohms balanced | ||
| Nominal level | +4 dBu (1.23 Vrms), -10 dBV (316 mVrms) | ||
| Maximum level (Hi-Z) | +7.6 dBu, unbalanced at 1% THD+N | ||
| Maximum level (600 ohm) | >+6.3 dBu, unbalanced at 1% THD+N | ||
| Audio delay | 1.5 frames | ||
| Control/remote | |||
| Serial control ports | |||
| Control | 1 bidirectional RS-232, 3.5 mm captive screw connector, 5 pole (uses 3 poles; shared with the alarm port) | ||
| Pass-through | 1 RS-232, 3.5 mm captive screw connector, 5 pole (3 pins are used, "RS-232 Over Fiber") | ||
| Baud rate and protocol | |||
| Control | 9600 baud, 8 data bits, 1 stop bit, no parity | ||
| Pass-through | 9600 to 115,200 baud | ||
| Serial control pin configurations | |||
| Captive screw connector | 1 = Tx, 2 = Rx, 3 = GND | ||
| Mini stereo jack | RS-232: tip = Tx, ring = Rx, sleeve = GND | ||
| Program control | Extron control/configuration program for Windows® Extron Simple Instruction Set (SIS™) | ||
| General | |||
| Power | Supplied by a PowerCage 1600 enclosure | ||
| Power consumption | 6.18 watts | ||
| Power input requirements | 12 VDC, 1.0 A, supplied by the PowerCage enclosure | ||
| Temperature/humidity | Storage: -40 to +158 °F (-40 to +70 °C) / 10% to 90%, noncondensing Operating: +32 to +122 °F (0 to +50 °C) / 10% to 90%, noncondensing | ||
| Cooling | Enclosure: fans, front to back Boards: convection, within the PowerCage enclosure | ||
| Thermal dissipation | 27.6 BTU/hr | ||
| Dimensions | Each board fits a double slot opening in a PowerCage enclosure. | ||
| Product weight | 1.1 lbs (0.5 kg) | ||
| Shipping weight | 2 lbs (1 kg) | ||
| Vibration | ISTA 1A in carton (International Safe Transit Association) | ||
| Regulatory compliance | |||
| Safety | CE, c-UL, UL | ||
| EMI/EMC | CE, C-tick, FCC Class A, ICES, VCCI | ||
| Environmental | Complies with the appropriate requirements of RoHS, WEEE. | ||
| Warranty | 3 years parts and labor | ||
| |||
| |||
