Описание товара
Подробности
The DXLink Multi-Format Decor Style Wallplate Transmitter sends analog or digital video including HDMI/HDCP, along with embedded audio or supplemental analog audio up to 100 meters to an Enova DGX Digital Media Switcher, compatible Enova DVX All In One Presentation Switcher or directly to a DXLink Receiver. It receives Power over DXLink* from the Enova DGX, Enova DVX (3155HD, 3156HD, or 2155HD), PS-POE-AT-TC High Power PoE Injector or PDXL-2 Dual Power over DXLink Controller over the twisted pair cable and features both a multi-format analog port to support legacy devices and an HDMI port to support newer digital devices.
Дополнительная информация
SPECIFICATIONS
GENERAL
Dimensions (HWD):
4 1/16" x 3 1/2" x 2 1/4" (10.31 cm x 8.84 cm x 5.72 cm)
Installation:
Mounts onto standard 2 gang US back boxes
Mounts into standard decor style wallplates (not included)
Mounts into standard decor style wallplates (not included)
Weight:
Approx. .75 lb (0.34 kg)
Shipping Weight:
Approx. 1.3 lb (.61 kg)
MTBF:
381,000 hours
Airflow:
Natural convection via air vent openings on front, back and top
Compatible AMX Products:
- Enova DGX 8/16/32/64 Digital Media Switchers
- Enova DVX-3155HD, DVX-3156HD and 2155HD All-In-One Presentation Switchers
- AVB-RX-DXLINK-HDMI DXLink HDMI Receiver Module as a point-to-point solution (when Wallplates are powered by PS-POE-AT-TC or PDXL-2)
- PS-POE-AT-TC High Power PoE Injector
- PDXL-2 Power over DXLink Controller
Recommended Accessories:
- CC-USB, USB Programming Cable (FG10-5965)
REGULATORY COMPLIANCE
FCC
CE EN 55022
CE EN 55024
CE EN 60950-1
IEC 60950-1
UL 60950-1
cUL
RoHS
WEEE
CE EN 55022
CE EN 55024
CE EN 60950-1
IEC 60950-1
UL 60950-1
cUL
RoHS
WEEE
DXLink TWISTED PAIR
Transport Layer Throughput (Max):
10.2 Gbps
Twisted Pair Cable Type:
Shielded Cat6, Cat6A and Cat7
DXLink twisted pair cable runs for DXLink equipment shall only be run within a common building where a common building is defined as: the walls of the structure(s) are physically connected and the structure(s) share a single ground reference
For more details and helpful cabling information, reference the white paper titledCabling for Success with DXLink, or contact your AMX representative
Twisted Pair Cable Length:
Up to 328 ft (100 m)
ACTIVE POWER REQUIREMENTS
DXLink Power:
Power must be supplied by a DXLink Power sourcing device such as:
- Enova DGX 8/16/32/64 Digital Media Switcher (with a DXLink Twisted Pair Input Board installed)
- Compatible Enova DVX All-In-One Presentation Switcher (3155HD, 3156HD or 2155HD)
- PS-POE-AT-TC High Power PoE Injector
- PDXL-2 Power over DXLink Controller
When installed in conjunction with an Enova DGX use the Enova DGX Configuration Tool located at AMX.com/enova to determine the power requirements of the configuration
AMX only supports the use of these approved Power over DXLink solutions. Other third party power supplies or non-compatible standard PoE solutions may damage the DXLink equipment. To use PS-POE-AT-TC or PDXL-2 as a power source the wallplates require firmware v1.2.40 or above
Power Connector:
Included on DXLink Connection
Power Consumption (Max):
Power over DXLink Supplied 7 W
POWER SUPPLY
External, Required:
Power must be supplied by a DXLink Power sourcing device such as:
- Enova DGX 8/16/32/64 Digital Media Switcher (with a DXLink Twisted Pair Input Board installed)
- Compatible Enova DVX All-In-One Presentation Switcher (DVX-3155HD, DVX-3156HD or DVX-2155HD)
- PS-POE-AT-TC High Power PoE Injector
- PDXL-2 Power over DXLink Controller
AMX only supports the use of these approved Power over DXLink solutions. Other third party power supplies or non-compatible standard PoE solutions may damage the DXLink equipment. To use PS-POE-AT-TC or PDXL-2 as a power source the wallplates require firmware v1.2.40 or above
ENVIRONMENTAL
Temperature (Operating):
32° to 104° F (0° to 40° C)
Temperature (Storage):
-22° to 158° F (-30° to 70° C)
Humidity (Operating):
5% to 85% RH (non-condensing)
Humidity (Storage):
0% to 90% RH (non-condensing)
Heat Dissipation (Max):
Power over DXLink supplied: 24 BTU/HR
FRONT CONNECTORS
User Accessible (accessible with faceplate mounted)
HDMI Input:
HDMI Type A Female
Analog Video Input:
HD-15 (Breakout cable required for non RGB formats)
Analog Stereo Input:
3.5mm Mini-Stereo Jack
USB (HID) Keyboard & Mouse:
USB Mini-B Connector
Setup Front Connectors (not accessible with faceplate mounted)
Advanced Configuration Interface:
USB Mini-B Connector
ID Pushbutton:
Toggle between DHCP and static IP addressing
Places system in NetLinx Device ID assignment mode
Reset the factory default settings
Restore the factory firmware image
Places system in NetLinx Device ID assignment mode
Reset the factory default settings
Restore the factory firmware image
Reset Pushbutton:
Resets/reboots the CPU of the wallplate
BACK CONNECTORS
DXLink Output:
RJ-45
CONTROL
Advanced Configuration Interface:
USB Mini-B Connector
INDICATORS
Power Indicator:
Green indicates whether or not the module is powered on
USB (HID)
USB (HID):
(1) USB Mini A/B Connector (“HOST”)
Use in conjunction with an Enova DGX Digital Media Switcher, connect a DXLink TX (twisted pair or fiber) to a PC and emulate keyboard and mouse commands from a DXLink Fiber Receiver (twisted pair or fiber)
For a list of HID devices which have been tested and found to be working well with the latest firmware please view the document “DXLink HID Keyboard and Mouse Supported Devices”.
Use in conjunction with an Enova DGX Digital Media Switcher, connect a DXLink TX (twisted pair or fiber) to a PC and emulate keyboard and mouse commands from a DXLink Fiber Receiver (twisted pair or fiber)
For a list of HID devices which have been tested and found to be working well with the latest firmware please view the document “DXLink HID Keyboard and Mouse Supported Devices”.
HDMI
Compatible Formats:
HDMI, HDCP, DVI
Input Signal Type:
HDMI
DVI-D (Single Link With Cable Adapter)
DisplayPort ++ (Input Only, With HDMI Cable Adapter)
DVI-D (Single Link With Cable Adapter)
DisplayPort ++ (Input Only, With HDMI Cable Adapter)
Input Connector:
HDMI Type A Female
Propagation Delay (Typ):
5 us
Input Voltage (Nominal):
1.0 Vpp Differential
Input Re-clocking (CDR):
Yes
Input Equalization:
Yes, Adaptive
Data Rate (Max):
4.95 Gbps / 6.75 Gbps
6.75 Gbps supported when the DXLink HDMI RX Scaler is in Bypass mode and format is 1080p60 or less
6.75 Gbps supported when the DXLink HDMI RX Scaler is in Bypass mode and format is 1080p60 or less
Pixel Clock (Max):
165 MHz / 225 MHz
225 MHz supported when the DXLink HDMI RX Scaler is in Bypass mode and format is 1080p60 or less
225 MHz supported when the DXLink HDMI RX Scaler is in Bypass mode and format is 1080p60 or less
Progressive Resolution Support:
480p up to 1920x1200 @ 60 Hz including but not limited to those resolutions shown in the DXLink Twisted Pair Transmitters/Receiver Instruction Manual
Interlaced Resolution Support:
480i, 576i, 1080i including but not limited to those resolutions shown in the DXLink Twisted Pair Transmitters/Receiver Instruction Manual. If input is interlaced, all scaled outputs will deinterlace video to a progressive resolution format. If in scaler Bypass mode interlaced input will pass through
Deep Color Support:
24-bit, 30-bit, 36-bit
30-bit, 36-bit supported when the DXLink HDMI RX Scaler is in Bypass mode and format is 1080p60 or less
30-bit, 36-bit supported when the DXLink HDMI RX Scaler is in Bypass mode and format is 1080p60 or less
Color Space Support:
RGB 4:4:4
YCbCr 4:4:4 and 4:2:2
(Input signal support for YCbCr 4:4:4 and 4:2:2, output color-space is converted to RGB 4:4:4)
YCbCr 4:4:4 and 4:2:2
(Input signal support for YCbCr 4:4:4 and 4:2:2, output color-space is converted to RGB 4:4:4)
3D Format Support:
Yes, when the scaler on corresponding output board or DXLink RX is set to Bypass mode
Frame Packing 1080p up to 24Hz
Frame Packing 720p up to 50/60Hz
Frame Packing 1080i up to 50/60Hz
Top-Bottom 1080p up to 24Hz
Top-Bottom 720p up to 50/60Hz
Side-by-Side Half 1080p up to 50/60Hz
Frame Packing 1080p up to 24Hz
Frame Packing 720p up to 50/60Hz
Frame Packing 1080i up to 50/60Hz
Top-Bottom 1080p up to 24Hz
Top-Bottom 720p up to 50/60Hz
Side-by-Side Half 1080p up to 50/60Hz
Audio Format Support:
Dolby TrueHD, Dolby Digital, DTS-HD Master Audio, DTS, 2 CH through 8 CH L-PCM Dolby Digital and DTS support up to 48kHz, 5.1 channels
Audio Resolution:
16 bit to 24 bit
Audio Sample Rate:
32 kHz, 44.1 kHz, 48 kHz, 96 kHz, 192kHz
Local Audio Support:
Yes for audio insertion
HDCP Support:
Yes, Supports AMX HDCP InstaGate Pro Technology When used with either an Enova DGX 8/16/32 Digital Media Switcher or DVX All-In-One Presentation Switcher the key support is up to 16 sinks per output, independent of source device
When used as a single point to point solution the key support is defined by the source device
When used as a single point to point solution the key support is defined by the source device
CEC Support:
None
DDC/EDID Support:
The HDMI EDID in point to point mode is passed up from the sink device.
When used with Enova DGX 8/16/32/64 Digital Media Switcher or Enova DVX-3155HD, DVX-3156HD or DVX-2155HD the HDMI EDID is passed from the Enova Switcher input to the TX and is user reprogrammable. The analog video input connection provides a fixed EDID set
When used with Enova DGX 8/16/32/64 Digital Media Switcher or Enova DVX-3155HD, DVX-3156HD or DVX-2155HD the HDMI EDID is passed from the Enova Switcher input to the TX and is user reprogrammable. The analog video input connection provides a fixed EDID set
ANALOG VIDEO
Compatible Formats:
RGBHV, RGBs, RGsB
YPbPr (HDTV)
Y/c (S-Video), C (Composite)
YPbPr (HDTV)
Y/c (S-Video), C (Composite)
Progressive Resolution Support:
480p up to 1920x1200 @ 60 Hz (reference the DXLink Twisted Pair Transmitters/Receiver Instruction Manual for extended list)
Interlaced Resolution Support:
480i, 576i, 1080i (reference DXLink Twisted Pair Transmitters/Receiver Instruction Manual for extended list)
If input is interlaced, all scaled outputs will deinterlace video to a progressive resolution format. If in scaler Bypass mode interlaced input will pass through unaltered
If input is interlaced, all scaled outputs will deinterlace video to a progressive resolution format. If in scaler Bypass mode interlaced input will pass through unaltered
Auto-Adjust Input:
Supported
RGB Input Signal Level Range:
1 Vpp nominal
RGB Input Impedance:
75 ohms
HV Sync Input Signal Level Range:
2 to 5 Vpp
HV Sync Input Impedance:
2.5 pF Typ, 10 pF Max
Digital Processing:
24 bit, 165 MHz
Y/Pb/Pr Input Signal Level Range:
1.0 Vpp for Y, 700 mVpp for Pb Pr
Y/Pb/Pr Input Impedance:
75 ohms
Y/c (S-Video) Input Signal Level Range:
1.0 Vpp for Y, 1.0 Vpp for c
Y/c (S-Video) Input Impedance:
75 ohms
C (Composite) Input Signal Level Range:
1.0 Vpp
C (Composite) Input Impedance:
75 ohms
Input Connector:
HD-15 (Breakout cable required for non RGBHV formats)
AUDIO (ANALOG & DIGITAL S/PDIF)
Input Signal Types:
Stereo Analog, S/PDIF
Video signal must be present to pass Audio
Video signal must be present to pass Audio
Analog Input Level (Max):
+2 dBu, unbalanced
Analog Input Impedance:
10k ohms
Analog to Digital Conversion:
48 kHz Sample Rate, 24-bit
S/PDIF Audio Format Support:
Dolby Digital, DTS, 2 CH L-PCM
Dolby Digital and DTS support up to 48kHz, 5.1 channels
Dolby Digital and DTS support up to 48kHz, 5.1 channels
S/PDIF Resolution:
16 to 24 bit
S/PDIF Sample Rate:
32 kHz, 44.1 kHz, 48 kHz, 96 kHz
S/PDIF Input Signal Level Range:
200 mVpp to 600mVpp terminated
S/PDIF Input Impedance:
75 ohms
Analog to Digital Reference Level:
+2.5 dBu = 0 dBfs
Input Connectors:
3.5mm Mini-Stereo Jack (Analog Stereo)
RCA Jack (S/PDIF)
RCA Jack (S/PDIF)
