Описание товара
Подробности
Модуль управления реверсивными двигателями электроштор, двухканальный для управления моторизированных жалюзи, экранов для проекторов, автоматических ворот и ставен потолочных световых люков. Каждый канал выполняет команды "вверх/вниз" и "открыть/закрыть" для управления стандартным реверсивным двигателем мощностью до 0,5 л.с., с напряжением до 240 В, использующим подключение по трехжильному кабелю.
- Двухканальный модуль управления реверсивными двигателями
- Работает в электросетях, использующих напряжение от 120 до 240 В с частотой 50/60 Гц
- Возможность ручного сброса состояния каналов
- Связь с системой управления через интерфейс Cresnet
- Возможность настройки с лицевой панели или с помощью ПО
- Функциональность прибора программируется через процессор Crestron DIN-AP2
- Устанавливается на DIN-рейку (ширина 6M)
Дополнительная информация
Load Ratings | ||
Motor Control Channels | 2 | |
Per Channel | 0.5 HP @ 240 Volts AC, 50/60 Hz | |
Module Total | 1 HP @ 240 Volts AC, 50/60 Hz | |
Load Types | 3-Wire bidirectional motors | |
Connections | ||
1 – 2 | (2) sets of (3) captive screw terminals; 3-wire bidirectional motor control relays; Maximum Wire Size: 12 AWG (2.5 mm²) | |
NET | (2) 4-pin 3.5mm detachable terminal blocks, paralleled; Cresnet slave port | |
OVERRIDE | (2) 2-pin 3.5mm detachable terminal blocks, paralleled; Sensing input for external low-voltage contact closure; Activates override mode when a closure is present; Minimum Closure Rating: 10mA (per module) at 24 Volts | |
Controls & Indicators | ||
OPEN & CLOSE 1 – 2 | (4) Red LEDs and (4) miniature pushbuttons for status indication and local control of each channel | |
NET ID | (2) 7-Segment green LED digits and (2) miniature pushbuttons for setting Cresnet ID | |
SETUP | (1) Red LED and (1) recessed miniature pushbutton for enabling setup mode and touch-settable ID | |
OVR | (1) Red LED and (1) miniature pushbutton for enabling override mode and saving override presets | |
PWR | (1) Green LED, illuminates when DC power is applied to the NET port | |
NET | (1) Yellow LED, indicates communication with the control processor | |
RESET | (1) Recessed miniature pushbutton, resets internal processor | |
Enclosure | ||
Light gray polycarbonate housing with polycarbonate label overlay, UL94 V-0 rated, 35mm DIN EN 60715 rail mount, DIN 43880 form factor for enclosures with 45mm front panel cutout, occupies 6 DIN module spaces (108mm) | ||
Power Requirements | ||
Cresnet Power Usage | 3 Watts (1.13 Amps @ 24 Volts DC) | |
Environmental | ||
Temperature | 32° to 104°F (0° to 40°C) | |
Humidity | 10% to 90% RH (non-condensing) | |
Heat Dissipation | 10 BTU/hr | |
Dimensions | ||
Height | 3.71 in (94.2 mm) | |
Width | 4.18 in (106.0 mm) | |
Depth | 2.35 in (59.5 mm) | |
Weight | ||
7.4 oz (210 g) |