Описание товара
Подробности
PowerCage® 1600 обеспечивает эффективный способ питания и установки нескольких передатчиков и приемников, упрощает интеграцию в большие системы. Монтируется в стойку, поддерживает широкий диапазон аудио-видео передатчиков и приемников Extron по оптоволокну и витой паре. PowerCage 1600 также имеет дополнительный резервный источник питания с возможностью оперативной замены, плюс активное управление мощностью и тепловыделением для оптимизации надежности в критически важных средах, где условие круглосуточной непрерывной работы имеет важное значение. Возможность оперативной замены и модульная конструкция позволяют заменять или добавлять платы в любое время, без выключения системы.
- Вмещает до 16 однослотовых или восемь двухслотовых многофункциональных плат
- Компактная конструкция, корпус 3U для установки в стойку
- Модульная, обновляемая и заменяемая на месте конструкция
- Интеллектуальное управление питанием
- Опциональный резервный блок питания
- Блок питания с возможностью «горячей» замены
Дополнительная информация
| Video — PowerCage FOX Tx/Rx VGA | |||
|---|---|---|---|
| |||
| Signal type | VGA-UXGA RGBHV, RGBS, RGsB, RsGsBs | ||
| Gain | Unity | ||
| Pixel data bit depth | 8 bits per channel, 3 channels (R, G, B) | ||
| Maximum resolution | 1600x1200 or 1080p @ 60 Hz, digitized pixel for pixel; higher resolutions up to 2048x1120, undersampled | ||
| Video input — PowerCage FOX Tx VGA | |||
| Number/signal type | 1 VGA-UXGA RGBHV, RGBS, RGsB, RsGsBs | ||
| Connector | 1 female 15-pin HD | ||
| Nominal levels | 0.7 Vp-p for RGB | ||
| Minimum/maximum levels | Analog: 0.3 V to 0.75 Vp-p with no offset, terminated | ||
| Impedance | 75 ohms | ||
| Horizontal frequency | 24 kHz to 100 kHz | ||
| Vertical frequency | 40 Hz to 120 Hz | ||
| Return loss | >40 dB @ 5 MHz | ||
| Video output — PowerCage FOX Rx VGA | |||
| Number/signal type | With input from a FOXBOX Tx VGA or a FOX 500 Tx: 1 VGA-UXGA RGBHV, RGsB (follows input or can be set by user) With input from a FOXBOX Tx VGA/YUV: 1 VGA-UXGA RGBHV, component video (bi- or tri-level YUV, 480p, 576p, 720p, 1080i, 1080p) | ||
| Connector | 1 female 15-pin HD | ||
| Nominal levels | 1 Vp-p for Y of component video 0.7 Vp-p for RGB and for R-Y and B-Y of component video | ||
| Minimum/maximum levels | 0.3 V to 0.75 Vp-p, terminated | ||
| Impedance | 75 ohms | ||
| Return loss | >30 dB @ 5 MHz | ||
| DC offset | ±5 mV with input at 0 offset | ||
| Video delay | 1-2 frames | ||
| Sync — PowerCage FOX Tx/Rx VGA | |||
| Input type | RGBHV, RGBS, RGsB, RsGsBs | ||
| Output type | RGBHV, RGsB (follows input or can be set by user) | ||
| Input level | 2.5 V to 5.0 Vp-p | ||
| Output level | TTL: 5.0 Vp-p, unterminated, on HV, for RGBHV, RGBS 0.3 Vp-p for component video (bi-level sync) or for Gs (SOG) 0.6 Vp-p for component video (tri-level sync) | ||
| Input impedance | 10k ohms | ||
| Output impedance | 75 ohms | ||
| Polarity | Positive or negative (follows input or can be set by user) | ||
| Video — PowerCage FOX Tx DVI, PowerCage FOX Tx/Rx DVI Plus | |||
| Resolution range | |||
| PowerCage FOX Tx DVI | Up to 1600x1200 or 1080p @ 60 Hz pixel for pixel; higher resolutions up to 1920x1200 @ 60 Hz, undersampled | ||
| PowerCage FOX Tx/Rx DVI Plus | Up to 1920x1200 or 1080p @ 60 Hz pixel for pixel | ||
| Formats | RGB and YCbCr digital video | ||
| Standards | DVI 1.0, HDMI | ||
| Video input — PowerCage FOX Tx DVI, PowerCage FOX Tx DVI Plus | |||
| Number/signal type | 1 single link DVI-D (or HDMI*) | ||
| Connector | 1 female DVI-I | ||
| |||
| Video output — PowerCage FOX Rx DVI Plus | |||
| Number/signal type | 1 single link DVI-D (or HDMI*) | ||
| Connector | 1 female DVI-I | ||
| Nominal level | 0.8 Vp-p | ||
| Video delay | 1-2 frames | ||
| Video — PowerCage FOX 3G HD-SDI | |||
| |||
| Signal type | HD-SDI, SDI, and 3G-SDI digital video signals | ||
| Gain | Unity | ||
| Resolution | 8 or 10 bits, automatic | ||
| Data rates | 270 Mbps, 1.485 Gbps, 2.970 Gbps | ||
| Operation standards | SMPTE 259M-C, SMPTE 292M, SMPTE 424M, ITU-R BT.601, ITU-R BT.1120 | ||
| Auto data rate lock | Yes | ||
| Video input — PowerCage FOX 3G HD-SDI transmitter | |||
| Number/signal type | 1 single link SDI, HD-SDI, or 3G-SDI digital component video | ||
| Connectors | 1 female BNC | ||
| Data rates | 19 Mbps to 2.97 Gbps | ||
| Nominal level | 0.8 Vp-p | ||
| Minimum/maximum levels | 0.5 V to 1 Vp-p with no offset | ||
| Impedance | 75 ohms | ||
| Return loss | ≥15 dB @ 5 MHz to 1.5 GHz ≥10 dB @ 1.5 GHz to 3 GHz | ||
| DC offset (max. allowable) | 5 V | ||
| Input coupling | AC | ||
| Input cable equalization | Automatic for up to -30 dB of cable loss | ||
| HD-SDI | 120 m (400') using Extron RG6 cable 90 m (300') using Extron RG59 cable | ||
| SDI | 150 m (500') using Extron RG6 cable 120 m (400') using Extron RG59 cable | ||
| |||
| Video output — PowerCage FOX 3G HD-SDI receiver | |||
| Number/signal type | 2 single link SDI, HD-SDI, or 3G-SDI digital component video | ||
| Connectors | 2 female BNC | ||
| Re-clocking | Automatic for 270 Mbps, 1.485 Gbps, 2.97 Gbps, or bypassed for unrecognized rates | ||
| Nominal level | 0.8 Vp-p | ||
| Minimum/maximum levels | 0.5 V to 1.0 Vp-p | ||
| Impedance | 75 ohms | ||
| Return loss | >25 dB @ 100 MHz | ||
| DC offset | ±5 mV with input at 0 offset | ||
| Video — PowerCage FOX Tx/Rx AV | |||
| |||
| Gain | Unity | ||
| Standards | |||
| Input | NTSC 3.58, NTSC 4.43, PAL, SECAM, autodetected | ||
| Output | NTSC 3.58, PAL (follows vertical rate) | ||
| Decoder type | Adaptive 2D, digital comb filter | ||
| Video input — PowerCage FOX Tx AV | |||
| Number/signal type | 1 component (Y, R-Y, B-Y), S-video, composite video | ||
| Connectors | 1 x 3 female BNC or 1 female 4-pin mini DIN for S-video | ||
| Nominal levels | 1.0 Vp-p for Y of component video and S-video, and for composite video 0.7 Vp-p for R-Y, B-Y of component video 0.3 Vp-p for C of S-video | ||
| Minimum/maximum levels | Analog: 0.3 V to 1.5 Vp-p with no offset | ||
| Impedance | 75 ohms | ||
| Return loss | >30 dB for Y/VID, B-Y/C, R-Y @ 5 MHz | ||
| Input coupling | AC | ||
| Video output — PowerCage FOX Rx AV | |||
| Number/signal type | 1 component (Y, R-Y, B-Y) video, S-video, composite video | ||
| Connectors | 1 x 3 female BNC or 1 female 4-pin mini DIN for S-video | ||
| Nominal levels | 1.0 Vp-p for Y of component video and S-video, and for composite video 0.7 Vp-p for R-Y, B-Y of component video 0.3 Vp-p for C of S-video | ||
| Minimum/maximum levels | 0.3 V to 1.5 Vp-p | ||
| Impedance | 75 ohms | ||
| Return loss | >40 dB @ 5 MHz | ||
| DC offset | +350 mV, maximum, with input at 0 offset | ||
| Video delay | 1-2 frames | ||
| Video — PowerCage FOX Tx/Rx HDMI | |||
| |||
| Maximum data rate | 4.25 Gbps | ||
| Maximum pixel clock | 165 MHz | ||
| Maximum resolution | 1920x1200 or 1080p @ 60 Hz, 8-bit color | ||
| Formats | RGB and YCbCr digital video | ||
| Standards | DVI 1.0, HDMI, HDCP 1.1, CEA-861E | ||
| Video input — PowerCage FOX Tx HDMI | |||
| Number/signal type | 1 single link HDMI | ||
| Connectors | 1 female 19-pin HDMI type A | ||
| Video output — PowerCage FOX Rx HDMI | |||
| Number/signal type | 1 single link HDMI | ||
| Connectors | 1 female 19-pin HDMI type A | ||
| Video processing — PowerCage FOX SR HDMI | |||
| Digital sampling | 24 bit, 8 bits per color, 165 MHz standard | ||
| Colors | 16.78 million | ||
| Video output — PowerCage FOX SR HDMI | |||
| |||
| Number/signal type | 1 single link HDMI (HDCP compliant) | ||
| Connectors | 1 female HDMI type A | ||
| Nominal level | 0.8 Vp-p | ||
| Video delay | 1-2 frames | ||
| Scaled resolution | 640x4806,8,9, 800x6006,8,9, 852x4806,8,9, 1024x7686,8,9, 1024x8526,8,9, 1024x10246,8,9, 1280x7686,8,9, 1280x8006,8,9, 1280x10246,8,9, 1360x7656,8,9, 1360x7686,8,9, 1365x7686,8,9, 1365x10246,8,9, 1366x7686,8,9, 1400x10506,8, 1440x9006,8,9, 1600x12006,8, 1680x10506,8, 1920x12006,8 HDTV: 480p7,8, 576p6, 720p3,4,5,6,7,8, 1080i6,7,8, 1080p1,2,3,4,5,6,7,8, 2048x10801,2,3,4,5,6,7,8 | ||
| 1 = 23.98 Hz, 2 = 24 Hz, 3 = 25 Hz, 4 = 29.97 Hz, 5 = 30 Hz, 6 = 50 Hz, 7 = 59.94 Hz, 8 = 60 Hz, 9 = 75 Hz | |||
| Video — PowerCage MTP T 15HD RSA, PowerCage MTP R 15HD RSA SEQ | |||
| Gain | Unity | ||
| Number/signal type | 1 set of proprietary analog signals | ||
| Connector | 1 female RJ-45 | ||
| Video input — PowerCage MTP T 15HD RSA | |||
| Number/signal type | 1 analog RGBHV, RGBS, RGsB, RsGsBs, component video (YUVi or YUVp/HDTV), S-video, or composite video | ||
| Connector | 1 female 15-pin HD | ||
| Nominal levels | 1 Vp-p for Y of component video and S-video, and for composite video 0.7 Vp-p for RGB and for R-Y and B-Y of component video 0.3 Vp-p for C of S-video | ||
| Minimum/maximum levels | 0.3 V to 1.45 Vp-p | ||
| Impedance | 75 ohms | ||
| Horizontal frequency | 15 kHz to 130 kHz | ||
| Vertical frequency | 30 Hz to 150 Hz | ||
| Return loss | <-30 dB @ 5 MHz | ||
| DC offset (max. allowable) | 250 mV | ||
| Video output — PowerCage MTP R 15HD RSA SEQ | |||
| Number/signal type | 1 analog VGA-UXGA RGBHV, RGBS, RGsB, RsGsBs, component video (YUVi or YUVp/HDTV), S-video, or composite video | ||
| Connector | 1 female 15-pin HD | ||
| Nominal levels | 1 Vp-p for Y of component video and S-video, and for composite video 0.7 Vp-p for RGB and for R-Y and B-Y of component video 0.3 Vp-p for C of S-video | ||
| Minimum/maximum levels | 0.3 V to 1.45 Vp-p | ||
| Impedance | 75 ohms | ||
| Return loss | <-30 dB @ 5 MHz | ||
| DC offset | <±35 mV with input at 0 offset | ||
| Skew compensation | 62 ns | ||
| Maximum resolution | Up to 1920x1200 or 2048x1080 or 1080p at 300' Up to 1024x768 at 600' | ||
| |||
| Sync — PowerCage MTP T 15HD RSA, PowerCage MTP R 15HD RSA SEQ | |||
| Input/output type | RGBHV, RGBS, RGsB, RsGsBs | ||
| Standards | NTSC 3.58, NTSC 4.43, PAL, SECAM | ||
| Input level (transmitter) | 3.5 V to 5.5 Vp-p, unterminated | ||
| Output level (receiver) | 4.0 V to 5.0 Vp-p, unterminated | ||
| Input impedance (transmitter) | 573 ohms ±5% | ||
| Output impedance (receiver) | 110 ohms | ||
| Polarity | |||
| Transmitter | Positive or negative (follows input polarity) | ||
| Receiver | Positive or negative (switch-selectable) | ||
| Video — PowerCage MTP T AV, PowerCage MTP R AV | |||
| Gain | Unity | ||
| Differential phase error | <1.0° at 3.58 MHz and 4.43 MHz | ||
| Differential gain error | <1.0% at 3.58 MHz and 4.43 MHz | ||
| Video input — PowerCage MTP T AV | |||
| Number/signal type | 1 S-video or composite video | ||
| Connectors | 2 female BNC | ||
| Nominal level | 1 Vp-p for Y of S-video and for composite video 0.3 Vp-p for C of S-video | ||
| Minimum/maximum levels | 0.3 V to 1.5 Vp-p with no offset | ||
| Impedance | 75 ohms | ||
| Return loss | <-30 dB, DC @ 10 MHz | ||
| DC offset (max. allowable) | 250 mV | ||
| Video output — PowerCage MTP R AV | |||
| Number/signal type | 1 S-video or composite video | ||
| Connectors | 2 female BNC | ||
| Nominal level | 1 V p-p for Y of S-video and for composite video 0.3 V p-p for C of S-video | ||
| Minimum/maximum level | 0.3 V to 1.5 Vp-p | ||
| Impedance | 75 ohms | ||
| Return loss | <-35 dB @ 5 MHz | ||
| DC offset | ±20 mV with input at 0 offset | ||
| Sync — PowerCage MTP T AV, PowerCage MTP R AV | |||
| Standards | NTSC 3.58, NTSC 4.43, PAL, SECAM | ||
| Audio — PowerCage FOX Tx/Rx VGA, PowerCage FOX Tx DVI, PowerCage FOX Tx/Rx DVI Plus, PowerCage FOX Tx/Rx AV, PowerCage FOX Tx/Rx HDMI, PowerCage FOX SR HDMI | |||
| |||
| Gain | |||
| Range | Adjustable, -18 dB to +10 dB | ||
| Default | Unbalanced output: -6 dB; balanced output: 0 dB | ||
| Frequency response | 20 Hz to 20 kHz, ±0.5 dB | ||
| THD + Noise | |||
| VGA, DVI, HDMI, SR HDMI boards | 0.10% @ 1 kHz at nominal level | ||
| AV boards | 0.15% @ 1 kHz at nominal level | ||
| S/N | >80 dB at maximum output (unweighted) | ||
| CMRR | 65 dB @ 20 Hz to 20 kHz | ||
| Audio bits per sample | 18 bits per channel, 2 channels (L, R) | ||
| Sampling rate | 48 kHz | ||
| Audio — PowerCage FOX AEX 104 | |||
| |||
| |||
| Gain | Unbalanced output: -6 dB; balanced output (default): 0 dB | ||
| Frequency response | 20 Hz to 20 kHz, ±0.5 dB | ||
| THD + Noise | 0.10% @ 1 kHz at nominal level | ||
| S/N | >80 dB at maximum output (unweighted) | ||
| Audio bits per sample | 18 bits per channel, 2 channels (L, R) | ||
| Sampling rate | 48 kHz | ||
| Audio input — PowerCage FOX Tx VGA, PowerCage FOX Tx DVI, PowerCage FOX Tx DVI Plus, PowerCage FOX Tx AV, PowerCage FOX Tx HDMI | |||
| Number/signal type | |||
| HDMI boards | 1 stereo, unbalanced or 2 mono, unbalanced | ||
| VGA, DVI, DVI Plus, and AV boards | 1 stereo, balanced/unbalanced or 2 mono, balanced/unbalanced | ||
| Connectors | |||
| HDMI boards | (1) 3.5 mm mini stereo jack | ||
| VGA, DVI, DVI Plus, and AV boards | (1) 3.5 mm captive screw connector, 5 pole | ||
| Impedance | ≥10k ohms unbalanced, ≥20k ohms balanced | ||
| Nominal level | |||
| HDMI boards | -10 dBV (316 mVrms) | ||
| All other FOX boards | +4 dBu (1.23 Vrms), -10 dBV (316 mVrms) | ||
| Maximum level | |||
| AV boards | +17 dBV, unbalanced at 1% THD+N | ||
| VGA, DVI, DVI Plus, and HDMI boards | +8.9 dBV, unbalanced at 1% THD+N | ||
| |||
| Audio output — PowerCage FOX Rx VGA, PowerCage FOX Rx DVI Plus, PowerCage FOX Rx AV, PowerCage FOX Rx HDMI, PowerCage FOX SR HDMI, PowerCage FOX AEX 104 | |||
| Number/signal type | |||
| AEX 104 boards | 4 stereo, balanced/unbalanced or 8 mono, balanced/unbalanced | ||
| All other FOX boards | 1 stereo, balanced/unbalanced or 2 mono, balanced/unbalanced | ||
| Connectors | |||
| AEX 104 boards | (4) 3.5 mm captive screw connectors, 5 pole | ||
| All other FOX boards | (1) 3.5 mm captive screw connector, 5 pole | ||
| Impedance | 50 ohms unbalanced, 100 ohms balanced | ||
| Nominal level | |||
| HDMI boards | -10 dBV (316 mVrms) | ||
| All other FOX boards | +4 dBu (1.23 Vrms), -10 dBV (316 mVrms) | ||
| Maximum level (Hi-Z) | |||
| VGA and DVI Plus boards | +7.6 dBu, unbalanced at 1% THD+N | ||
| AV boards | >+19 dBu, unbalanced at 1% THD+N | ||
| HDMI and AEX 104 boards | >+11.0 dBu, balanced at 1% THD+N | ||
| Maximum level (600 ohm) | |||
| VGA and DVI boards | >+6.3 dBu, unbalanced at 1% THD+N | ||
| AV boards | >+15 dBm, unbalanced at 1% THD+N | ||
| HDMI and AEX 104 boards | >+10.0 dBu, balanced at 1% THD+N | ||
| Audio delay | 1.5 frames | ||
| Audio — PowerCage MTP T 15HD RSA, PowerCage MTP R 15HD RSA SEQ, PowerCage MTP T AV, PowerCage MTP R AV | |||
| Number/signal type | 1 set of proprietary analog signals | ||
| Connector | 1 female RJ-45 | ||
| Gain | Unbalanced output: 0 dB; balanced output: +6 dB | ||
| Frequency response | 20 Hz to 20 kHz, ±1 dB | ||
| THD + Noise | 0.15% @ 1 kHz, 0.3% @ 20 kHz at nominal level | ||
| S/N | >70 dB at maximum output (unweighted) | ||
| Stereo channel separation | >60 dB @ 1 kHz | ||
| CMRR | >43 dB @ 20 Hz to 20 kHz | ||
| Audio input — PowerCage MTP T 15HD RSA, PowerCage MTP T AV | |||
| Number/signal type | |||
| PowerCage MTP T 15HD RSA | 1 stereo, unbalanced | ||
| PowerCage MTP T AV | 1 stereo, balanced/unbalanced | ||
| Connector | (1) 3.5 mm captive screw connector, 5 pole | ||
| Impedance | |||
| PowerCage MTP T 15HD RSA | >10k ohms, unbalanced | ||
| PowerCage MTP T AV | >10k ohms, unbalanced; >20k ohms, balanced; AC coupled | ||
| Nominal levels | +4 dBu (1.23 Vrms), -10 dBV (316 mVrms) | ||
| Maximum level | +18 dBu, (unbalanced) at 1% THD+N | ||
| |||
| Audio output — PowerCage MTP R 15HD RSA SEQ, PowerCage MTP R AV | |||
| Number/signal type | |||
| PowerCage MTP R 15HD RSA SEQ | 1 mono, balanced/unbalanced | ||
| PowerCage MTP R AV | 2 mono, balanced/unbalanced | ||
| Connector | (1) 3.5 mm captive screw connector, 5 pole | ||
| Impedance | 50 ohms unbalanced, 100 ohms balanced | ||
| Gain error | ±1 dB channel to channel | ||
| Nominal levels | +4 dBu (1.23 Vrms), -10 dBV (316 mVrms) | ||
| Maximum level | +18 dBu, unbalanced at 1% THD+N | ||
| Control/remote | |||
| |||
| Serial control ports | |||
| Enclosure | 1 bidirectional RS-232, 2.5 mm mini stereo jack (front panel) | ||
| PowerCage FOX boards | |||
| Control | 1 bidirectional RS-232, 3.5 mm captive screw connector, 5 pole (uses 3 poles; shared with the alarm port) | ||
| Pass-through | 1 RS-232, 3.5 mm captive screw connector, 5 pole (3 pins are used, "RS-232 Over Fiber") | ||
| PowerCage MTP 15HD boards | External device; pass-through, uni- or bidirectional Input/output: 1 set of proprietary signals on a female RJ-45 jack Output/input: 1 RS-232 via 3 poles of a 3.5 mm captive screw connector (3 pole for transmitter, 5 pole for receiver) | ||
| Baud rate and protocol | |||
| PowerCage FOX boards | |||
| Control | 9600 baud, 8 data bits, 1 stop bit, no parity | ||
| Pass-through | 9600 to 115,200 baud | ||
| PowerCage MTP 15HD boards | |||
| Baud rates | Up to 38400 bps at up to 600' (182.9 m) (Higher data rates and distances are possible. Performance varies based on baud rate and cable length.) | ||
| Protocol | Data bits = 5 - 8 Stop bits = 1 or 2 Parity = odd, even, none Flow control = XON, XOFF, none Defaults: 8 data bits, 1 stop bit, no parity | ||
| |||
| Serial control pin configurations | |||
| Captive screw connector | |||
| PowerCage FOX boards | 1 = Tx, 2 = Rx, 3 = GND | ||
| PowerCage MTP 15HD boards | Transmitter: 1 = Tx, 2 = Rx, 3 = GND Receiver: 3 = GND, 4 = Tx, 5 = Rx | ||
| Mini stereo jack | RS-232: tip = Tx, ring = Rx, sleeve = GND | ||
| Program control | For FOX boards only: Extron control/configuration program for Windows® Extron Simple Instruction Set (SIS™) | ||
| General | |||
| Recommended cable type | For PowerCage MTP boards: Extron Enhanced Skew-Free™ AV UTP cable or CAT 5/5e/6 (shielded or unshielded) | ||
| Power supply | Internal, 1 or 2* (positive-negative), primary and redundant, hot-swappable 100-240 VAC, 50-60 Hz *A redundant power supply is optional. | ||
| Power consumption | |||
| System | Enclosure without boards: 12.4 watts | ||
| Individual FOX boards | FOX Tx VGA: 5.68 watts FOX Rx VGA: 6.54 watts FOX Tx DVI: 5.67 watts FOX Rx DVI: 5.50 watts FOX 3G HD-SDI: 1.84 watts FOX Tx AV: 6.89 watts FOX Rx AV: 5.57 watts FOX DVI Plus Tx: 5.68 watts FOX DVI Plus Rx: 6.18 watts FOX Tx HDMI: 6.02 watts FOX Rx HDMI: 6.02 watts FOX SR HDMI: 8.8 watts FOX AEX 104: 7.9 watts | ||
| Individual MTP boards | MTP T 15HD RSA: 4.30 watts MTP R 15HD RSA SEQ: 8.38 watts MTP T AV: 2.69 watts MTP R AV: 3.92 watts | ||
| Power input requirements for boards | 12 VDC, 1.0 A, supplied by the PowerCage enclosure | ||
| Temperature/humidity | Storage: -40 to +158 °F (-40 to +70 °C) / 10% to 90%, noncondensing Operating: +32 to +122 °F (0 to +50 °C) / 10% to 90%, noncondensing | ||
| Cooling | Enclosure: fans, front to back Boards: convection, within the PowerCage enclosure | ||
| Thermal dissipation | |||
| FOX SR HDMI board | 29.8 BTU/hr | ||
| FOX AEX 104 | 27.0 BTU/hr | ||
| All other boards | 27.6 BTU/hr | ||
| Mounting — PowerCage enclosure | |||
| Rack mount | Yes | ||
| Enclosure type | Metal | ||
| Enclosure dimensions | |||
| PowerCage enclosure | 5.25" H x 17.0" W x 12.25" D (3U high, full rack wide) 13.3 cm H x 43.2 cm W x 31.2 cm D (Depth excludes connectors on the optional boards. Width excludes rack ears.) | ||
| PowerCage FOX boards | Each fits a double slot opening in a PowerCage enclosure. | ||
| PowerCage MTP R 15HD RSA SEQ | Each fits a double slot opening in a PowerCage enclosure. | ||
| All other boards | Each fits a single slot opening in a PowerCage enclosure. | ||
| Product weight | |||
| PowerCage enclosure | 11.6 lbs (5.3 kg) | ||
| PowerCage FOX boards | 1.1 lbs (0.5 kg) | ||
| PowerCage MTP R 15HD RSA SEQ | 1.0 lbs (0.5 kg) | ||
| All other boards | 0.8 lbs (0.4 kg) | ||
| Shipping weight | |||
| PowerCage enclosure | 13 lbs (6 kg) | ||
| Boards | 2 lbs (1 kg) each | ||
| Vibration | ISTA 1A in carton (International Safe Transit Association) | ||
| Regulatory compliance | |||
| Safety | CE, c-UL, UL Additionally for FOX boards: FDA Class 1 | ||
| EMI/EMC | CE, C-tick, FCC Class A, ICES, VCCI | ||
| Environmental | Complies with the appropriate requirements of RoHS, WEEE. | ||
| Warranty | 3 years parts and labor | ||
| |||
| |||
